Kawasaki C7478 Manuel d'utilisateur

Please read this manual and save it with your original sales receipt.Tools needed for assembly: Phillips Screwdriver, Hammer and Pliers (all not inclu

WasherRear WheelDriverCap NutCap NutAssembly ToolHubcap• Slide a washer onto the rear axle.• Slide the rear wheel driver onto the rear axle. Makesure

AssemblyTM• Press the tab under the back of the seat and lift to remove the seat.• Make sure the motor harness wires are positioned inthe channel to p

Assembly12• Lift the front end of the vehicle.• Slide the straight end of the steering column through thehole in the upper steering linkage and out th

Assembly13• Fit the front handlebar assembly into the front of the handlebar.ScrewPegsScrewPegsHolesHolesHandlebarFrontHandlebarHousing• Fit the handl

R®Assembly14• Bend the plastic tip at the end of the microphone cord sothat it forms a "T".• Insert the "T" end of the microphone

Label DecorationG15Proper label application will help to keep the labels looking their best! When applying labels, keep the followingguidelines in min

IMPORTANT! Use only a Power Wheels®12 volt batterywith built-in thermal fuse. Use of any other battery willdamage your vehicle. Make sure that you cha

If a battery leak develops, avoid contact with the leakingacid and place the damaged battery in a plastic bag. See information below for proper dispos

Teach Safety Rules to ChildrenWhile children can quickly develop the skill necessary todrive this vehicle, it is important to remember that theirjudgm

• Make sure the shifter is in the LOW SPEED position.• Press the foot pedal. The vehicle will drive forward at amaximum of 21/2 mph.• Help your child

Table of ContentsImportant InformationA Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IMPORTANT! To avoid damaging the motors and gears, stop the vehicle before shifting between low and high speed.• Make sure the shifter is in the HIGH

Problems and Solutions GuideIMPORTANT! If you experience a problem with your vehicle, first check the Problems and SolutionsGuide below. If you still

Problems and Solutions GuideShort run time Undercharged battery Charge the battery. A new battery should have beencharged for at least 18 hours befor

Problems and Solutions GuideProblem Possible Cause SolutionWhen the foot pedal is pressed Operation of vehicle in low speed It is possible that only o

PRINTED IN MEXICO C7478pr-0920IMPORTANT!DO NOT use this vehicle for the first time until you havecharged the battery for 18 hours.Remember to…✔Charge

CAUTION• In the unassembled state, this package contains small parts. Adult assembly is required.• Use the charger in dry locations only.WARNING• Prev

PartsCWheel - 4• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather thanreturn this produc

All Shown Actual SizePart Not Shown: Label Sheet.437 Cap Nut – 67/16" Washer - 412 Volt BatteryCap NutAssembly ToolMicrophone12-VOLTCHARGER12 Vol

Parts DiagramD1. Vehicle Body2. Cowling3. Seat4. Wheel - 45. Hubcap - 46. Cap Nut - 67. Steering Column8. Handlebar Neck9. 12 Volt Battery 10. 12 Volt

Battery ChargingEAbout Thermal FusesYour Power Wheels®12 volt battery is equipped with abuilt-in thermal fuse. The thermal fuse is a self-resettingsaf

Battery Charging• Plug the charger connector into the battery .• Plug the charger into a standard 120 volt wall outlet .Note: If power flow to the w

2Assembly• Fit a .437 cap nut onto one end of the rear axle.• Tap the other end of the rear axle with a hammer tosecure the cap nut on the end of the