Kawasaki NINJA 74110 Manuel d'utilisateur

Kawasaki®Ninja®Owner’s Manual with Assembly InstructionsPlease read this manual and save it with your original sales receipt.For Model 74110Tools need

• Slide a washer onto one of the front axles.• Slide a round bushing, ring side first, onto the same frontaxle.• Slide a wheel (ribbed side first) ont

TM11Assembly• Press the tab under the back of the seat and lift toremove the seat.• Fit the rectangular opening in the cowling over the shifterhandle.

• Lift the front end of the vehicle.• Slide the straight end of the steering column through thehole in the upper steering linkage and out through theh

13AssemblySteeringColumnHandlebarNeckRibGrooveSoundBoxHandlebarHousing -Bottom Half• Slide the bottom half of the handlebar housing onto theend of the

Assembly• Fit the front fairing onto the handlebar assembly. Makesure that the screw tabs on the handlebar assembly arealigned with the screw pegs on

R15Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelinesin mind:• Wash your ha

TM®®®®VOLTRECHARGEABLEBATTERY POWERED3TM®®VOLTRECHARGEABLEBATTERY POWERED416Right SideLeft SideLabel Decoration121518125262526132524101720621261325267

17Important Note: Use only a Power Wheels®12 voltbattery with built-in thermal fuse. Use of any other batterywill damage your vehicle. Make sure that

If a battery leak develops, avoid contact with the leakingacid and place the damaged battery in a plastic bag. See information below for proper dispos

10°Incline should never be more than 10°5. Do not operate this vehicle with more than one rider,seated on the seating area. A child who is not sitting

2Table of ContentsImportant InformationA Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

• Make sure the shifter is in the LOW SPEED position.• Press the foot pedal. The vehicle will drive forward at amaximum of 21/2 mph.• Help your child

21Advanced Use - High Speed DriveBefore you disconnect the high speed lock-out, make sureyour child knows how to start and stop the vehicle andknows t

22Problems and Solutions GuideIMPORTANT! If you experience a problem with your vehicle, first check the Problems and SolutionsGuide below. If you stil

23Problems and Solutions GuideVehicle was running but Loose wire or loose connectors Check all wires and connectors. Make sure the motorsuddenly stopp

24Problems and Solutions GuideProblem Possible Cause SolutionVehicle runs sluggishly Undercharged battery Charge the battery. A new battery should hav

ALABAMABIRMINGHAM - Frigid Service & Sales, 701 Graymont Ave. North, 35203, (205) 323-5831BIRMINGHAM - Frigid Service & Sales, 1861 Centerpoin

Authorized Service CentersSHELTON - Jeff’s Appliance, Inc., 500A Howe Avenue, 06484,(203) 924-8997STAMFORD - Appliance Servicenter of Stamford, 15 Ced

27MISSISSIPPIHATTIESBURG - Champion Cycle & Fitness, 104 South 37thAvenue, 39401, (601) 264-8233IUKA - W. H. Fairless Hardware Co., Inc., 117 Fult

AUSTIN - Harrell Supply and Service, Inc., 1409 West Oltorf,78704, (512) 442-5966AUSTIN (ROUND ROCK) - Harrell Supply, 907c InterstateHighway 35, 7866

WARNING• Children can be harmed by small parts, sharp edges and sharp points in the vehicle’sunassembled state, or by electrical items. Care should be

PartsCWheel - 4• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather thanreturn this produc

All Shown Actual SizeNot Shown: Label Sheet, Literature Bag11/2" Screw – 2Cap Nut – 8*7/16" Washer - 6*Radio Knob - 212 Volt BatteryHex Bush

Parts DiagramD61. Vehicle Body2. Cowling3. Seat4. Wheel - 45. Hubcap - 46. Cap Nut - 67. Steering Column8. Right Mudflap9. 12 Volt Battery10. Key Asse

CAUTIONUse the charger in dry locations only.Battery ChargingEWARNING• The battery must be handled by adultsonly. The battery is heavy and containssul

Battery ChargingPb• Plug the charger connector into the battery .• Plug the charger into a standard 120 volt wall outlet .Note: If power flow to the

Assembly93• Position the vehicle body upside down.Note: The mudflaps are marked “R” and “L” to designateright and left.• With the “R” marking facing u